Here is a full list of advanced settings (parameters) for ZEN71 On/Off Switch:
Some parameters were added in later firmware updates so please make sure you're on the latest firmware to have all of the settings below available.You can view the change log for the ZEN71 here.
On/Off Paddle Orientation
Parameter 1:Choose if you want the upper paddle to turn the light on or turn the light offwhen tapped.
Values:0 – Upper paddle turns the light on,lower paddle turns it off (default); 1 – Upperpaddle turns the light off, lower paddle turns iton; 2 – Any paddle turns light on/off.
Size:1 byte dec
LED Indicator Control
Parameter 2:Choose if you want the LEDindicator to turn on when the switch (light) ison or off, or if you want it to remain on or off atall times.
Values:0 – LED indicator is on when switch isoff, LED indicator is off when switch is on(default); 1 – LED indicator is on when switch ison, LED indicator is off when switch is off; 2 –LED indicator is always OFF; 3 – LED indicatoris always ON.NOTE:tap the upper paddle 6 times quickly to change this mode.
Size:1 byte dec
Parameter 14:Choose the color of the LED indicator.
Values:0 – white; 1 – blue (default); 2 – green; 3 – red.
Size:1 byte dec
Parameter 15:Choose the LED indicator'sbrightness level.
Values:0 – bright (100%); 1 – medium (60%); 2 – low (30%). Default: 1.
Size:1 byte dec
Parameter 19: Enable / disable LED indicator for setting changes. Choose if you want the LED indicators to flash whenever a parameter (settings) is adjusted on the device to confirm the change. Disable this feature if you're using the LED indicators in automations.
Values:0 – LED indicators flash to confirm a setting change (default);1 - LED indicators don't flash if a setting is changed. Default: 0.
Size:1 byte dec
Auto Turn-Off Timer
Parameter 3:Use this parameter to enable ordisable the auto turn-off timer function (thetime after which you want the switch toautomatically turn off once it has been turnedon).
Values:0 – timer disabled (default); 1 – 65535(minutes).
Size:4 byte dec
Auto Turn-On Timer
Parameter 5:Use this parameter to enable ordisable the auto turn-on timer function (thetime after which you want the switch toautomatically turn on once it has been turnedoff).
Values:0 – timer disabled (default); 1 – 65535(minutes).
Size:4 byte dec
On Off Status After Power Failure
Parameter 8:Set the on off status for theswitch after power failure.
Values:0 – forced to OFF (regardless of stateprior to power outage); 1 – forced to ON(regardless of state prior to power outage); 2 –remembers and restores on/off status afterpower failure (default)
Size:1 byte dec
Enable/Disable Scene Control
Parameter 9:Enable or disable scene controlfunctionality for quick double tap triggers.
Values:0 – scene control disabled (default). 1 –scene control enabled.
Size:1 byte dec
Parameter 18:Enable scene control functionality from the momentary switch in a 3-way installation.
Values:0 – scene control disabled commands from the remote 3-way switch disabled (default). 1 –scene control commands from the remote 3-way switch enabled. Default: 0
Size:1 byte dec
Smart Bulb Mode: Enable/Disable Paddle / Z-Wave Control
Parameter 11:Enable or disable local on/offcontrol. If enabled, you’ll only be able tocontrol the connected light via Z-Wave. Scenesand other functionality will still be availablethrough paddles.
Values:0 – physical paddle control disabled. 1 – physical paddle control enabled (default). 2 – physical paddle and Z-Wavecontrol disabled.
NOTE:hold the lowerpaddle for 10 seconds until the LED indicator starts blinking, then within 2 seconds, tap the upper paddle 5 times quickly to change this mode. The LED indicator will stay solid green for 3 seconds to confirm the change.
FOR FIRMWARE 10.20, 2.20 AND 3.10 (800LR) (or higher):Hold the UPPER paddle for 10 seconds until the LED indicator starts blinking, then within 2 seconds, tap the upper paddle 5 times quickly to change this mode. The LED indicator will stay solid green for 3 seconds to confirm the change.
Size:1 byte dec
Parameter 13:Set reporting behavior for disabled physical control.
Values:0 – switch reports on/off status and change LED indicator state even if physical and Z-Wave control is disabled (default). 1 – switch doesn't report on/off status or change LED indicator state when physical (and Z-Wave) control is disabled.
Size:1 byte dec
3-Way Switch Type
Parameter 12:Choose the type of 3-way switch you want to use with this switch in a 3-way set-up.
Values:0 – regular mechanical 3-way on/off switch, use the connected 3-way switch to turn the light on or off (default); 1 – momentary switch, click once to change status (light on or off)
Size:1 byte dec
Association Reports
Parameter 7: Choose which physical and Z-Wave triggers should prompt the switch to send a status change report to the associated devices.
Values:0 – none; 1 – physical tap on ZEN71only;2 - physical tap on connected 3-way switch only; 3 - physical tap on ZEN71or connected 3-way switch; 4 -Z-Wave command from hub; 5 -physical tap on ZEN71or Z-Wave command from hub; 6 -physical tap on connected 3-way switch or Z-Wave command from hub; 7 -physical tap on ZEN71/ connected 3-way switch or Z-Wave command from hub; 8 -timer only; 9 -physical tap on ZEN71or timer; 10 -physical tap on connected 3-way switch or timer; 11 -physical tap on ZEN71/ connected 3-way switch or timer; 12 -Z-Wave command from hub or timer; 13 - physical tap on ZEN71, Z-Wave command from hub, or timer; 14 -physical tap on ZEN71/ connected 3-way switch, Z-Wave command from hub, or timer; 15 -all of the above. Default: 15.
Size:1 byte dec
Parameter 16:Choose how the switch reports its status back to the hub.
Values:0 – Binary switch report for Z-Wave control, basic set report for paddle control; 1 – binary switch report for both Z-Wave and paddle control(default)
Size:1 byte dec
Enable/Disable Programming on the Paddles
Parameter 17:Enable or disable programming functionality on the switch paddles. If this setting is disabled, then inclusion, exclusion, smart bulb mode no longer work when switch paddles are activated (factory reset and scene control will still work) - that means you can now use triple-tap triggers on the switch for scenes and remote control of other devices.
Values:0 – programming enabled (default). 1 –programming disabled.
Size:1 byte dec
MANUAL CONTROL
Upper Paddle:
1 x tap: load on; Scene 1, attribute 00
2 x tap: Scene 1, attribute 03
3 x tap: enter inclusion (pairing)mode (only if the switch is not included to the hub); Scene 1, attribute 04
4 x tap:Scene 1, attribute 05
5 x tap:Scene 1, attribute 06
6 x tap: change LED indicator mode (see parameter 2)
held:Scene 1, attribute 01
released:Scene 1, attribute 02
held for 10 seconds (LED indicator starts blinking): enter the setting menu >>5 x tap up to change smart bulb mode (see parameter 11)
Lower Paddle:
1 x tap: load off; Scene 2, attribute 00
2 x tap: Scene 2, attribute 03
3 x tap: enter exclusion (unpairing)mode; Scene 2, attribute 04
4 x tap:Scene 2, attribute 05
5 x tap:Scene 2, attribute 06
held:Scene 2, attribute 01
released:Scene 2, attribute 02
held for 10 seconds (LED indicator starts blinking): enter the setting menu >> 5 x tap down for factory reset; 2 x tap down to enable the range test tool.
Supported Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
COMMAND_CLASS_SWITCH_BINARY_V2,
COMMAND_CLASS_CONFIGURATION_V4,
COMMAND_CLASS_CENTRAL_SCENE_V3,
COMMAND_CLASS_ASSOCIATION_V3,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3,
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3,
COMMAND_CLASS_TRANSPORT_SERVICE_V2,
COMMAND_CLASS_VERSION_V3,
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1,
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1,
COMMAND_CLASS_INDICATOR_V3,
COMMAND_CLASS_POWERLEVEL_V1,
COMMAND_CLASS_SECURITY_2,
COMMAND_CLASS_SUPERVISION_V1,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
How to Access the Advanced Settings:
SmartThings
Hubitat
Vera
Home Assistant
All ZEN71 switches can be updatedvia OTA firmware updates, here is how to do that.After youregister your productandcreate an account here, you canaccess all firmware files here. Questions? Feel free toreach outto our customer service, we're here 7 days a week!
